<address id="wf6lp"><ol id="wf6lp"></ol></address><tt id="wf6lp"><address id="wf6lp"></address></tt>

        1. <source id="wf6lp"></source>
          <b id="wf6lp"></b>

        2. <small id="wf6lp"><kbd id="wf6lp"></kbd></small><source id="wf6lp"><menu id="wf6lp"></menu></source>
          EN | 中文

          Selection of raw materials for interior and exterior latex paint

          Publication time:2018.08.17 10:30

          Times of browsing:

          Selection of raw materials for interior and exterior latex paint

           

          Yang wenyuan (taizhou silian chemical co., LTD., 225312)

           

          Abstract: the selection of raw materials for interior and exterior latex paint is discussed in order to produce high cost effective latex paint.

           

          Keywords: interior wall latex paint; Exterior wall latex paint; The raw materials

           

          Article no. : 1009-1696 (2012) 04-0044-03

           

          Practical technology

           

          0 the introduction

           

          In the past ten years, it should be said that China's economy has been developing rapidly

           

          Ten years, of course, is the architectural paint rapid development stage. According to the

           

          Statistics show that the annual output of China's construction coating was 3,518,000 tons in 2010

           

          Annual production was six times in 2001. Average annual paint usage per person is a measure

           

          The bellwether of national economy and people's living standard. With developed countries

           

          Than, the use amount of building coating per capita still is very low in our country. Statistically, I

           

          The per capita construction paint consumption in China is 2.6kg /a, and the per capita construction paint in cities and towns

           

          The material usage amount is 5.5 kg/a, while that of building coating per capita in developed countries such as Europe and America

           

          Material usage: over 25 kg/a. With China's future urbanization process

           

          The acceleration of urban population growth, coupled with urban and rural for housing

           

          Demand improvement, decoration demand will further rise in the foreseeable

           

          In the future, the demand for interior and exterior wall coatings will still be on the rise.

           

          There is a lot of room for improvement of architectural paint usage in China.

           

          As the demand for interior and exterior emulsioni paint continues to rise in recent years

           

          A large number of medium - sized paint production enterprises. Although the exterior wall latex

           

          Paint production technology gradually mature, but with the scale of large enterprises

           

          Production, small businesses are increasingly struggling, many even

           

          Without their own professional technical staff, the paint product formula is either one

           

          Some high quality raw materials piled up, or some inferior raw materials pool

           

          Set, coating performance stability and overall profits are also discounted.

           

          This paper attempts to combine the author's experience in the process of the shallow

           

          The formulation, raw material selection and production process control of exterior and interior latex paint are discussed

           

          Uniform elements.

           

          Basic formula of inner and outer wall emulsion paint

           

          With GB/T 9756-2009 "synthetic resin emulsion interior wall coating" and

           

          GB/T 9755-2001 "synthetic resin emulsion exterior wall paint" as an example

           

          Formula of internal and external emulsioni paint (see table 1). Additional, inside wall emulsioni paint return

           

          Mandatory standard GB 18582-2008 must be met.

           

          Table 1. Basic formula of exterior and interior latex paint

           

          Table 1 The formulation of interior/exterior latex paint

           

          Interior wall emulsion paint base formula (white) exterior wall emulsion paint base formula (white)

           

          Serial number material name quantity /‰

           

          1 water 250 1 water 120

           

          2 wetting agent PE100 1 2 wetting agent PE100 1

           

          3 dispersant SN5040 6 3 dispersant SN5040 6

           

          4 defoamer NXZ 1 4 defoamer NXZ 1

           

          5 propylene glycol 10 5 propylene glycol 10

           

          6 preservative LXE 2 6 preservative LXE 1.5

           

          7 anatase titanium 60 7 rutile titanium 120~150

           

          84,000 megasolinite 80~100 8 heavy calcium 150~250

           

          9 800 mesh heavy calcium 150~250 9 barium sulfate 50

           

          10 barium sulfate 60 10 wollastonite 40

           

          11 talc powder 40 11 styrene emulsion 240~260

           

          12 styrene-acrylic emulsion 120 12 film forming assistant

           

          TEXANOL

           

          5 to 7

           

          13 film forming assistant

           

          TEXANOL

           

          5~7 13 defoaming agent NXZ 1.5~2

           

          14 defoaming agent NXZ 1.5~2 14 rheology auxiliaries appropriate

           

          15 suitable amount of the rheological agent 15 suitable amount of cellulose thickening agent

           

          16 cellulose thickener appropriate amount of 16 alkali swelling thickener appropriate

           

          17 moderate amount of alkali swelling thickener 17 moderate amount of water

           

          18 a moderate amount of water

           

          PH regulator micro amount

           

          No.4 45

           

          2. Selection of raw materials for emulsion paint

           

          2.1 the emulsion

           

          Emulsion is the most important film forming material in the inner and outer wall emulsion paint.

           

          For internal wall emulsion paint, generally use vinegar emulsion, vinegar tertiary emulsion, benzene

           

          Acrylic emulsion; For exterior wall latex paint, pure propyl emulsion, silicon-propyl emulsion,

           

          Styrene-acrylic emulsion. At present in China, most of the interior and exterior latex paint is benzene

           

          Acrylic emulsion, because of its cost - effective acceptance. To reach the inner wall latex

           

          Performance requirements of lacquer GB/T 9756 -- 2009, in basic formula design,

           

          The most important is the number of times of washing, the emulsion in the formula

           

          Generally 10.5%~12.5%.

           

          2.2 selection of preservatives and fungicides

           

          Whether preservative or fungicide, the variety on the market

           

          Are very complex, the principles of selection are generally efficient, low toxicity, compatibility,

           

          Stable, durable and cost-effective. Use of formaldehyde is becoming increasingly popular

           

          Type of preservative, through its slow release, to achieve a certain degree of germicidal efficacy,

           

          It not only has the advantages of formaldehyde, but also avoids the disadvantages of formaldehyde. general

           

          In the formula, the amount of preservative is 0.1%~0.3%, the use of anti - mildew agent

           

          Content is 0.3% ~ 0.6%. For products that require special mildew resistance, choose

           

          It is better to use two or more fungicides. Fungicides are mainly used

           

          Prevent the wet areas where rain is abundant from producing mildew on the walls and dry in the north

           

          Area production USES emulsioni paint, most enterprises do not add anti - mildew agent.

           

          2.3 selection of wetting dispersant

           

          The wetting, dispersing, and stabilizing of pigments is often closely linked,

           

          Wetting is the process of particle replacement on pigment surface. Disperse is the pigment in

           

          The process of separation under the action of external forces; Stability is the final dispersal

           

          The pigment granules no longer condense twice. The common wetting agent for latex paint is

           

          Cognis PE100; The commonly used dispersants are polyacrylate and polyacrylate

           

          Polyphosphate. In practice, 0.2% polyphosphate and

           

          A mixture of 0.2% to 0.4% polyacrylate. Storage stability of coatings,

           

          Washing resistance is a key index to evaluate dispersant.

           

          2.4 selection of antifoaming agent

           

          Antifoaming agents can be divided into antifoaming agents and defoaming agents. Antifoaming agent has been on

           

          The foaming agent is on the coating surface

           

          The surface plays a role in destroying the bubbles that have formed. In the production of latex paint

           

          In control, antifoaming agents are usually added twice, at the pulping stage and in paint making

           

          Add 1/2 to each stage. Or 2/3 in the pulping stage and 2/3 in the paint stage

           

          In the third. At the stage of pulping, it is best to add a defoaming agent with strong anti-foam effect.

           

          In the paint stage it is best to add the foam breaking ability strong anti - foam agent.

           

          2.5 selection of film forming auxiliaries

           

          The emulsion itself is thermoplastic, so in order to guarantee the film performance,

           

          You don't want it to be too soft, and you want it to be as hot as possible.

           

          Corresponding production of emulsion paint the lowest film temperature is higher, so low temperature

           

          Construction and film formation become a problem, which is through the addition of film auxiliary

           

          To balance.

           

          The amount of film forming AIDS generally depends on the amount of emulsion, but

           

          The vitrification temperature of emulsion also affects the amount of film additives

           

          Big. In addition, such as propylene glycol, ethylene glycol such as antifreeze agent is also certain

           

          And the amount of them to the amount of the film forming AIDS

           

          It has an impact. Furthermore, with the increase of PVC (pigment volume concentration),

           

          That is, the amount of emulsion reduced, the film is more difficult, because with the face filling

           

          The adhesion of the material to the film forming agent greatly reduces the efficiency of the film forming agent.

           

          Most of the production of film additives in the paint phase of emulsion Tim

           

          After adding, such production if the operation is not good, film auxiliary

           

          So that the emulsion quickly polymerized into small particles and coarse, so must be stirred at low speed

           

          Mix slowly in the mix, so that the film agent to play the largest role. There are also

           

          It is added before the painting stage, although it is safer to do so

           

          Hydrophobic film forming AIDS will be wetted by emulsifying, and face filler in advance

           

          Adhesion, the actual effectiveness of film - forming AIDS will be greatly reduced.

           

          The dosage of film forming assistant should be based on the emulsion, adding process, formula,

           

          The different of season, area will be treated flexibly, its regular dosage is emulsion use

           

          0.05 times the amount.

           

          2.6 selection of thickeners

           

          Latex paint is water as the dispersing medium of the paint, and water viscosity

           

          Very low, can not meet the construction requirements, need thickening agent to adjust the flow

           

          Degeneration. Commonly used thickeners are cellulose, non - associative alkali swelling

           

          Type ii and associative alkali swelling type thickeners, their properties are shown in table 2.

           

          Table 2 properties of various thickeners

           

          Table 2 The characteristics of various thickeners

           

          Comparison of cellulose non-associative alkali swelling type association alkali swelling type

           

          The thickening efficiency is higher and higher

           

          PH sensitivity is generally very high

           

          Poor splash resistance is better

           

          Poor leveling is generally good

           

          Flow resistance is better, better and better

           

          The optical retention is generally good

           

          Better water resistance, better and better

           

          Good alkali resistance is general

           

          The prices are higher, moderate and cheaper

           

          Yang wenyuan: the choice of raw material of latex paint for inner and outer walls

           

          Shanghai paint volume 50

           

          It can be seen from table 2 that various thickeners have different advantages and disadvantages in milk

           

          In the paint system, if only one thickening agent is used, the storage stability,

           

          Construction effect and other aspects are difficult to achieve the expected performance, most of them are adopted

           

          Two or more thickeners are used to achieve the desired effect.

           

          2.7 choice of fillers

           

          Take white latex paint as an example, rutile titanium dioxide is the best

           

          White pigment. In our country most manufacturer, interior wall emulsioni paint makes more

           

          Use anatase titanium; use rutile titanium; In the developed countries

           

          The interior and exterior walls are basically rutile - type titanium white.

           

          Commonly used fillers are calcium carbonate, talc powder, sericite powder, gao ling

           

          Soil, silica fume, lithopone, quartz powder, ultrafine aluminum silicate, sulfuric acid

           

          Barium, etc.

           

          Both heavy and light calcium belong to calcium carbonate, of which heavy calcium is the natural mineral

           

          Stone is crushed and light calcium is a synthetic product. Among the many fillers, weight

           

          Calcium should be said is in emulsioni paint usage amount is the biggest, most stable, cheapest

           

          Packing; Although light calcium also has a little dry covering power, suspension is also good,

           

          But easy to start white frost, stability is poorer.

           

          Many interior wall latex paint formulations also use a little talcum powder, though

           

          It is easy to powder, but can improve the construction and leveling of emulsion paint.

           

          Sericite powder belongs to layered silicate, is scale crystal, acid resistant

           

          Good alkali resistance and chemical stability. It can be used in exterior and interior latex paint

           

          Appropriate use, on the one hand can greatly improve the weather resistance of paint film, prevent

           

          Water vapor penetration, on the other hand to prevent powder and paint cracking.

           

          Another important filler is kaolin, which is easily dispersed in water, white

           

          High degree, strong dry covering, thixotropic, paint stability

           

          And in good shape. Through experimental study, we found that the ultrafine 4 000 order

           

          Kaolin and titanium dioxide can be used to improve the covering power of the coating

           

          Comprehensive performance. In white latex paint, silica fume has a bright color

           

          Adjust, can enhance the hardness of paint film, but also improve the durability and resistance of the film

           

          Grinding.

           

          According to the characteristics of the different fillers described above, the inner wall latex paint in general

           

          Products with high whiteness such as heavy calcium, light calcium, talc powder and kaolinite;

           

          Sericite, barium sulfate, wollastonite powder,

           

          Calcined kaolin, etc. Should choose flexibly according to price, demand.

           

          3 conclusion

           

          Although at present the production technology of emulsioni paint is increasingly mature with the technology

           

          The increasingly progressive innovation of art is still developing, while our country until the 20th century

           

          In the early 1990s, with the entry of multinational companies into China brought new

           

          Material, new technology, just begin rapid development. Improve cost performance and increase

           

          Function, low cost, low VOC (volatile organic compounds), low gas

           

          Taste, environment friendly type emulsioni paint will become the mainstream.

           

          To obtain high cost performance emulsion paint required to fine the relevant raw materials

           

          For in-depth comparative research and selection, not raw material piling, no

           

          To obtain good market returns, we must optimize the formulation.

           

          The Selection of Raw Materials for Interior/Exterior Latex Paint

           

          Yang Wenyuan (Taizhou Quad Chemical Co., Ltd., Jiangsu Taizhou, 225312, China)

           

          Abstract: The selection of raw materials for interior/exterior latex paint were brief discussed in order to prepare The

           

          Latex paint with high price performance ratio.

           

          Key Words: interior latex paint; Exterior latex paint; Raw material

           

          Akzo Nobel powder paint released 2012 Interpon F furniture color trend

           

          Recently, akzo Nobel powder paint released the latest Interpon F 2012 color trend designed specifically for the furniture industry.

           

          The latest Interpon F color trend is at the forefront of today's color trends. This series product has 15 kinds of indoor furniture color and 15 kinds of outdoor furniture color

           

          Colors are available.

           

          The latest popular collection is refreshingly based on akzo Nobel's "color trend" series, showing the latest in the furniture market

           

          Color and surface effect trends. Designers can not only have excellent performance and excellent protection of Interpon F powder coating into their own products, at the same time

           

          It also ensures that its design is in line with the latest color trends.

           

          Based on the color trend, akzo Nobel also released the Interpon F color and gloss standard color card, which will help designers better understand

           

          Interpon F's choice of different colors and sheen.

           

          Interpon F furniture powder coating follows the fashion trend, durable and provides first-class protective effect. It can fully meet the durability of the furniture industry and beauty

           

          2021中文字幕亚欧乱码,怡春院怡红院在线2017|日本有码_1页_777,久久大香香蕉国产免费网动漫,1024手机看片你懂的无码|制服丝袜 视频一区 图片专区|老司机永久免费视频网站|japan色系videos护士|亚洲欧美AV中文日韩二区试看